17-Cl-35(n,p)

ID 119
Type H - High priority request
Target 17-Cl-35
Reaction (n,p)
Quantity SIG - Cross section
Incident energy 100 keV - 5 MeV
Accuracy 5-8 %
Field(s) Fission
Subfield Gen-IV
Accepted date 17-Apr-2022
Status Work in progress
Latest review date 28-Apr-2022

Requester: Tom Taylor (Moltex Energy) and Tommy Cisneros (TerraPower)

 

Project (context)

Gen-IV (fast chloride molten salt reactor design)

Impact

 

There is currently large uncertainty in reactivity for chloride fast reactors, due mainly to the uncertainty in the Cl-35 (n,p) cross section at high energies. This is a difficulty for chloride fast reactor design because the required fissile loading has large uncertainty, and this uncertainty also propagates to other parameters important to safety, such as reactivity coefficients. Production of S-35 via this reaction is also important for corrosion.

Additionally, above 1.2 MeV there is no uncertainty available for Cl-35 (n,p) in any evaluated library, except TENDL. This makes it difficult to justify a reasonable total uncertainty.

A number of organisations are designing or studying chloride fast reactors and are therefore sensitive to this nuclear data. In addition to Moltex Energy and TerraPower (MCRE and MCFR) the CEA is performing chloride fast reactor R&D. Previous work led by EDF R&D on the REBUS-3700 fast chloride reactor also concluded that more accurate nuclear data for Cl was needed (Mourogov & Bokov, 2006).

It is also worth noting that other Cl nuclear data is important for chloride fast reactors, particularly Cl-35 (n,gamma) and Cl-36 capture, for Cl-36 waste considerations.

 

Accuracy

 

To achieve a target k-eff uncertainty < 300 pcm, the table below suggests uncertainties < 2% would be required above ~100 keV. However, such a low uncertainty is unlikely to be achievable using differential measurements. k-eff uncertainty > 300 pcm would be tolerable, given the uncertainty is currently estimated to be at least ~1000 pcm. On this basis a target of 5 – 8 % is suggested.

It is realised that it may be challenging to achieve even this uncertainty. Any reduction in uncertainty, and/or improved covariances, would be valuable. Integral experiments would likely be needed to reduce uncertainties to a level of 2 – 3 %.

 

Justification document

 

33 group sensitivity coefficients have been generated for the main output parameters, as part of a collaboration with ANL (using the PERSENT code and ENDF/B-VII.0 data). Those for Cl-35 (n,p) are large, as expected, see attached Figure 1.

Uncertainties and target uncertainties have then been derived by UPM through WPEC SG46, using this sensitivity data. Using the TENDL-2021 evaluation for Cl-35, and ENDF/B-VII.1 otherwise, gives a total uncertainty of 836 pcm, with 631 pcm from Cl-35 alone, and dominated by the (n,p) cross section (595 pcm, next largest 173 pcm from (n,alpha)). Below is a table showing target accuracy requirements for the top 10 most important reactions for the Moltex SSR-W.

Recent measurements in the US (Batchelder et al., 2019) and (Kuvin et al., 2020) also indicate that the cross section in all libraries could be too high above ~1.2 MeV. Direct perturbation of the Cl-35 (n,p) reaction in this energy range shows large sensitivity (increase of ~1000 pcm for reduction by 50% between 2.23 and 3.68 MeV).

TerraPower indicates also that very recent measurements (Warren, 2021) of the 35Cl(n,p) cross section have significantly disagree with the evaluated nuclear data in ENDF/B-VIII.0 that was not updated in the last update of chlorine nuclear data – ENDF/B-VII.1. The attached Figure 2 presents the discrepancy between evaluated data and recent measurements.

 

Comment from requester

 

The tables below are reproduced, with permission, from A Review of the Nuclear Data Adjustment Activities within WPEC Sub-groups, O. Cabellos, WANDA 2022, March 2022.

Target accuracy requirements for total k-eff uncertainty < 300 pcm, with nuclear data from ENDF/B-VII.1 (Cl-35 uncertainty from TENDL-2021).

Rank# Reaction Energy group Current (%) Target (%) Rel. unc. reduction (%)
1 Cl35(n,p) 2 6.6 0.9 37.4
2 Cl35(n,p) 3 12 1.6 14.9
3 Pu239(n,gamma) 4 8.4 1.3 12
4 Cl35(n,p) 1 8.4 1.2 8.9
5 Pu239(n,gamma) 3 10.4 2.0 4.6
6 Fe56(n,elastic) 3 9.2 1.9 4.3
7 Fe56(n,gamma) 3 16.8 2.8 1.8
8 Pu240(n,gamma) 2 59.3 4.2 1.8
9 Cl35(n,p) 4 11.1 3.7 1.5
10 Fe56(elastic) 2 5.4 1.9 1.3

Boundaries of energy groups

Group# Lower energy (eV) Upper energy (eV) Description
1 2.23130E+06 1.96403E+07 Above threshold fertile
2 4.97871E+05 2.23130E+06 Above threshold inelastic
3 6.73795E+04 4.97871E+05 Continuum to URR
4 2.03468E+03 6.73795E+04 URR
5 2.26033E+01 2.03468E+03 RRR
6 5.40000E-01 2.26033E+01 Epithermal
7 1.40000E-05 5.40000E-01 Thermal

Entry status

Work in progress (as of SG-C review of May 2022)

Main recent references

Please report any missing information to hprlinfo@oecd-nea.org